Triumph 1200 Series
(Factory Pro "TD12" Series)

 


sample picture

Long Boy Fuel Screw set 

$99.95 / 4
pn: CRZ-SCR-5020M

 with new screws, springs, washers and o-rings

1. Choose your shipping method

2.
 

"Long Boy"

Finger and screwdriver adjustable extended Fuel Screw

Frustrated with trying to find an "almost 90 degree"  screwdriver to fine adjust your fuel screws for best idle and cruise?
Use Factory Pro's new "finger adjustable" fuel screws to adjust fuel screws for best throttle response. Traveling to high altitude? It's easy to lean out the lowend temporarily.

Make your life easier.

Installation:
Remove old short stock fuel screws, old o-rings, old washers and old spring. The o-ring might be stuck in the carb, so, take a light and make sure it's really out if it didn't come out with the screw (or you can't find it after you took out the screw)
Use a small bent wire to pull it out if it doesn't drop out. Keep the old parts for "spares".

Fuel screw set comes with:
4 Long Boy fuel screws
4 new o-rings
4 new washers
4 new springs

   

 
CRB-TD12-1.0
Up to 99 and beyond,  Daytona 1200, Trophy 1200 w/ 36mm MIKUNI carbs

$159.95
Legacy Kit

1. Choose your shipping method

2.

Best "drop-in" kit available for the 36mm Mikuni CV carb equipped Triumph 1200's.

Boosts power a bit at full throttle, improves throttle response and wheelie ability. Definitely pulls harder out of 2nd and 3rd gear corners.
Factory Pro manufactures stock replacement needle jet / emulsion tubes for the stock Mikuni carbs.

For 1200's with Mikuni carburetors.


Hello Marc,

For two years ago I have ordered in the Netherlands the CRB-TD12-1.1-TI kit for my Daytona 1200. ('95-60.000 km)

The problem before was, no smooth at lower rpm and in cold condition it was necessary for at least 10 minutes to use the choke. The information about this I found on your site. Never heard before about emulsion tubes who are worn. I removed them, then looked to them with help of a magnifying glass and I was wondering about the wear of the tubes. The same as the pictures you showed on your site!!!!

After installing the kit, everything changed. Smooth everywhere, decreased full-consumption, increased power, the choke was a great help the first ten seconds, after this period, not necessary anymore. A great solution.

For two weeks ago I ordered for the same bike an ignition advancer but they send me the wrong, it was the advancer for the three cylinder. No problem, I have more Triumphs and installed it on my '95 T-bird (60.000 km). Ha, ha, it helps really. Increase of power and.......... from 2nd to 3rd gear a wheelie, for the first time since 13 years!!!!

Thanks again!!!

Louis - Netherlands / 2008, 04, 10
 

 

CRZ-EMU-100102k
Needle jet / emulsion tube

$132 set of 4

1. Choose your shipping method

2.

The stock Triumph 1200 needle jets (incorporated into the top of the emulsion tube on the 36mm Mikuni carb) wear out in as little as 8000 miles of "in town" driving on Mikuni carbs, causing excess fuel delivery that cannot be compensated for by lowering the fuel level. Generally, if your bike has 10,000+ miles and the mileage is very poor, the needle jets / emulsion tubes are the first thing to replace to get back to "like new" mileage.
 
Check out emuworn.html for more needle jet wear information.

UK buyers: Purchase Direct on this website.

Make your 1200 shift better than it ever did - even when new -



(not correct picture)

SHFT-PRO-TD09   $159.95
(3 week lead time)
replaces:
arm 1190022-T0301
spring 1190335-T0301
clutch cover gasket not included

1. Choose your shipping method

2.

 

 

Pro Shift Kit

Tired of lazy, clunky shifting?  Tired of missing the 1-2 shift?

Factory Pro's famous Pro Shift Kits are now available for the early 900 and 1200 models.

Improved Factory Pro designed and manufactured Micro bearing Detent Arm and Factory Pro Detent Spring will firm up shift feel and virtually eliminate missed shifts - both up shifting and downshifting.

Shifts quicker. Misses fewer shifts. Feels RIGHT.
Perfect to install when working on the clutch.

Remove the RH engine cover  - the clutch assembly, bolt in the kit.

Includes: Factory Pro Micro bearing Detent Arm and Factory Pro Detent Spring.
(This kit does not include a clutch cover gasket)

Installation: Less than 2 hours to install with impact wrench and large socket set.

Can I install it myself?
Yes - If you can remove the clutch assembly, you can do this.
 

 

The parts to be replaced are under the clutch assembly.

1-2 hours labor.

ignition advance plates - 1200cc


(sample picture only)

RTR-TRI-27-04     $99.95

1. Choose your shipping method

2.

Ignition Advancer

Adding an Ignition Advancer will perk up the low and midrange and sometimes increases mileage.


General Technical Support

Needle jet wear w/ Mikuni carbs


Looking for your idle mixture screws?  Here is where they are located:
Note that this is for 900cc and 1200c bikes with Mikuni carbs!


Tech Notes:

You can use cams and intake boots from the Thunderbird and install them into the Legend for a +10-15hp increase.

 


Subject:  RE: Triumph Sprint Sport 900 , 1998
Date:  Mon, 2 Oct 2000 13:05:09 -0400
From:  Greene_Jeff@emc.com
To:  factory2@ix.netcom.com

Hi Marc,

I have installed the kit. The Sprint now screams ( as loud as a Sprint can anyway).

Thanks for making the kit. You may want to contact Jack Lilley (http://www.jacklilley.com/cart/index.htmin) the UK. They were not aware that you made a jet kit for the Triumph's. Also, some of your distributors (Tucker-Rocky) did not list the kits for the Triumphs.

Thanks again,
Jeff Greene

 

 

Absolutely NO carb parts sold in California.

New and improved Suzuki Teka SFI  2

with new TPS display and "MMT" Memory Module Tuner

Finally - Quick, easy, cost effective Suzuki tuning with no expensive "add-on boxes"
Suzuki cruisers and sportbikes

Please click here for more info

Contact Factory Pro
M-F, 9am - 5pm, Pacific time, -7 or -8 GMT

800 869-0497
 USA and Canada

415 491-5920

parts information
 info@factorypro.com

EC997 dynamometer information
info@factorypro.com

Product Support /Tech SECTION
click here

 

Mailing / Shipping address:

Factory Pro
179 Paul Drive
San Rafael, CA 94903
USA

And most importantly
Restart back at the HOME page and click on the red box in the top left to find the bike that you want parts for...
restart at HOME page

 

This Tuning Site has been visited by
  
people.
www.digits.net - the oldest counting service on the web

          

 

 

 

LINKS
EFI and Carb Tuning - Most all FI and carb tuning

by Wheelsmith Racing

Flight Training - train with AMA race winner Todd Harrington.

The Harringtons own American Flyers, one of the most established flight training facilities in the USA.

 8 locations

 800-362-0808
The Rich Oliver Mystery School will help you discover your hidden inner strength. 
It will challenge you. It will teach you a new way of thinking, and a new way of riding. You can take your riding to an exciting new level!  

We use a variety of proven drills and training techniques. 
Practicing these techniques with our Yamaha dirt track trainers will enhance your abilities both on the track or the street.  

It doesn't matter what you ride or race, the Rich Oliver Mystery School improves everyone's skill level and mindset!

WW2 vintage flying Special

Book a sightseeing flight over the Wine Country or a Kamikaze aerobatic flight or a biplane flight over famous Sonoma Raceway, the Golden Gate Bridge and the San Francisco Bay for one or two during the spring and get a free souvenir t shirt!
(NEW!  Ask about the P-40 flights!)

707 938 2444

Just tell them that you saw this on the Factory Pro website!
Marc
Northern California's most unforgettable flying experience.  No experience required.  Open weekends!

The extension of the laboratory for engines of the Swiss Federal Institute of Technology was completed in about 1935. Its architect was Rudolf Otto Salvisberg (1882-1940). He had a successful career in Berlin but returned to Switzerland after the advent of the Nazis. His architectural style was somewhat similar to that of Erich Mendelsohn. The staircase of the laboratory is in normal use but well preserved.
Edited to the tunes of Chemical Residue by Herbie Hancock.